000-837 1, schema
[ Pobierz całość w formacie PDF ] GSI Fitting Instructions /Inbouwinstructie /Manuel de Montage / Einbauanleitung Instruction Nr./Instructienr./No. d’instruction/Einbauanleitungs Nr. :265000-837*1 Make / Merk / Marque / Marke :Lada Car type/Auto type/Automobile type/Typ :112 1.6 8V Year of construction/Bouwjaar/Année de fabrication/Modelljahr :’05---> Engine code/Motorcode/Numero du moteur/Motorkode :- Injectionsystem/Injectiesysteem/Injectionsysteme/Steuergerät :Bosch Motronic Motorkit Nr. /Motorsetnr. /No. Kit moteur /Motorkit Nr. :260100-645 GENERAL INSTRUCTIONS When installing the GSI LPG installation,compliance is required with the following guidelines: * This manual is based on dutch regulations. It’s the installer’s responsibility to check the local regulations and to make all necessary adaptions * Before commencing the installation of the LPG installation, remove the negative terminal from the battery. * If necessary, consult the workshop manual of the relevant car before the parts are disassembled. * All directions in the installation manual are given from the direction of the traffic. * Unless indicated otherwise, all measurements are in mm. * When drilling be careful for the underlying parts! * Deburr holes in the plating and treat them for rust. * First check the measurements given and the wire colours and positions. * The holes for the injectors must be drilled in accordance with the instructions. Use the correct drilling jig,if indicated. * When fitting the injector nipples, vacuum nipples, water nipples, gas nipples and LPG valve, use sealing locking agent on the screwthread. * Mount the GSI injector in line with the injector holder. * Always oil the O-rings of the injector holders. * Use the right hose clips when fitting all hoses. * After installing the LPG installation, ensure a watertight seal on the cable and pipe lead-throughs. * Use the connectors supplied for electrical connections and then insulate them completely. Do not solder! * Prevent the risk of damage from wiring harnesses and hoses. Fasten them with the cable ties supplied * Check the entire installation for leaks once installation is completed. * Adjustment for a car with GSI LPG installation: Adjust the operating pressures of the vaporiser/pressure regulator when the engine is at operating temperature: 1st stage: 1400 mbar - 2nd stage: 1000 mbar This adjustment must always be made immediately after the installation of the LPG installation! ALGEMENE INSTRUCTIES Bij de inbouw van de GSI-autogasinstallatie dienen de volgende richtlijnen in acht te worden genomen: * Deze instructie is gebaseerd op de nederlandse inbouwvoorschriften. Het is de verantwoording van de inbouwer om de lokale regels te controleren en de nodige aanpassingen uit te voeren. * Neem voordat met de inbouw van de autogasinstallatie wordt begonnen de minpool van de accu los. * Raadpleeg, indien nodig, het werkplaatshandboek van de betreffende auto voordat onderdelen worden gedemonteerd. * Alle richtingen in de inbouwhandleiding zijn aangegeven vanuit de rijrichting. * Alle maten zijn, tenzij anders aangegeven, vermeld in mm’s. * Let bij het boren op de onderliggende delen. * Gaten in het plaatwerk aangebracht ontbramen en tegen roest behandelen. * Controleer vooraf de opgegeven maten en draadkleuren en posities. * Het boren van de gaten voor de injectoren moet volgens de instructies gebeuren. Indien aangegeven de juiste boormal gebruiken. 265000-837*1 17-05-2005 1/12 www.teleflexgfi.nl Lada 112 1.6 8V Bosch Motronic ‘05 GSI Fitting Instructions /Inbouwinstructie /Manuel de Montage / Einbauanleitung * Bij de montage van de injectornippels,vacuumnippels,waternippels,gasnippels en LPG-afsluiter een afdichtend borgmiddel op de schroefdraad gebruiken. * Monteer de GSI-injector in lijn met de injectorhouder. * Gebruik altijd olie op de O-ringen van de injectorhouders. * Alle slangen monteren met de juiste slangklemmen. * Na inbouw van de autogasinstallatie de kabel- en leidingdoorvoer waterdicht afwerken. * Electrische verbindingen uitvoeren met de bijgeleverde verbindingconnectors en daarna afisoleren. Niet solderen! * Voorkom dat kabelbomen en slangen kunnen beschadigen. Leg deze vast met de bijgeleverde binders * Controleer de gehele installatie op lekkage als de inbouw gereed is. * Afstelling voor auto met GSI autogasinstallatie: Stel de werkdrukken van de verdamper/drukregelaar af als de motor op bedrijfstemperatuur is. 1e trap : 1400 mbar - 2e trap : 1000 mbar Deze afstelling moet altijd direct na inbouw van de autogasinstallatie uitgevoerd worden ! INSTRUCTIONS GENERAL Règles de montage de l’installation gaz GSI: * Cette manuel d”instruction est bassé sur normes neerlandais. C”est la responsabilité de mechanicien de vér normes locales ! * Veuillez déconnecter, avant le montage de l’installation gaz la borne négative de la batterie. * Consultez, si nécessaire, le manuel d’atelier de la voiture concernée avant le démontage des pièces. * Toutes les indications du manuel de montage sont données suivant l’ordre chronologique des opérations à effectuer. * Toutes les mesures sont, sauf autrement indiquées, en mm. * Faites attention aux pièces latérales pendant les perçages. * Les trous réalisés dans la tôle doivent être ébavurés et protégés contre la rouille. * Contrôler à l’avance les mesures, les couleurs des fils et les positions indiquées. * Le perçage des trous pour les injecteurs doit être fait selon l’instruction de montage. Si indiqué,utiliser le gabarit spécifique. * Au montage des raccords injecteurs, raccords à dépression, raccords d’eau, raccords de gaz et électrovanne principale, utilisez un produit de scellement sur le filet. * Toujours utiliser de l’huile sur les joints, en montant les injecteurs. * Placer l’injecteur GSI précisément dans l’axe de sa coupelle et sans contrainte. * Serrer les tuyaux avec les colliers correspondant aux diamètres. * Après le montage, assurer l’étanchéité des passages faisceaux et canalisations. * Réaliser les connections électriques avec les connecteurs livrés et puis isoler. Ne pas souder! * Attachez les faisceaux, câbles et tuyaux pour éviter tous frottements. * Après le montage, contrôler l’étanchéité gaz, essence et eau sur tous les circuits et raccords. * Règlage de l’ installation GSI: Règler la pression de travail du détendeur quand la voiture est en température de fonctionnement. Première étage 1400 mbar – Deuxième étage 1000 mbar. Ce règlage doit être effectué directement après le montage de l’installation gaz! ALGEMEINE ANWEISUNGEN Die folgenden Richtlinien müssen beim Einbau einer GSI-Autogasanlage befolgt werden: * Diese Anweisungen richten sich nach der niederländischen Einbauvorschriften. Es unterliegt der alleinigen Verantwortung des Installateurs um die örtlichen Regeln zu kontrollieren und die erforderlichen Anpassungen auszuführen. * Vor dem Einbau der Autogasanlage den Minuspol der Batterie abklemmen. * Falls erforderlich, vor dem Ausbau von Fahrzeugteilen zuerst im diesbezüglichen Werkstatthandbuch nachschlagen. * Alle Richtungsanweisungen in dieser Einbauanleitung beziehen sich auf die Fahrtrichtung. * Sofern nicht anders vermerkt, sind alle Maße in mm angegeben. * Beim Bohren auf die unterliegenden Teile achten. * In den Blechplatten gebohrten Löcher entgraten und gegen Rost behandeln. * Die angegebenen Maße, Drahtfarben und Positionen vor dem Einbau kontrollieren. * Beim Anbringen von Bohrlöchern für die Injektoren müssen die Anweisungen streng befolgt werden. Falls angegeben, die korrekte Bohrschablone verwenden. * Zum Abdichten der Injektor-, Unterdruck-, Wasser- und Gasnippel sowie des LPG-Ventils, beim Einbau auf dem Schraubengewinde ein Dichtmittel anbringen. * Den GSI-Injektor auf einer Linie mit dem Injektorhalter einbauen. * Die O-Ringe der Injektorhalter immer mit Öl benetzen. * Für alle Schläuche die passenden Schlauchklemmen verwenden. * Nach dem Einbau der Autogasanlage die Kabel- und Leitungsdurchführung wasserdicht abdichten. * Für die elektrischen Anschlüsse die mitgelieferten Steckverbinder verwenden und danach abisolieren. Nicht löten! * Kabelbäume und Schläuche vor Beschädigungen schützen. Diese mit den mitgelieferten Kabelbindern befestigen. * Nach dem Einbau die gesamte Anlage auf Lecks überprüfen. * Einstellen von Fahrzeugen mit GSI-Autogasanlagen: Den Betriebsdruck des Verdampfers/Druckreglers einstellen, wenn der Motor die Betriebstemperatur aufweist: 1. Stufe: 1400 mbar – 2. Stufe: 1000 mbar Diese Einstellungen müssen immer unmittelbar nach dem Einbau der Autogasanlage durchgeführt werden! 265000-837*1 17-05-2005 2/12 www.teleflexgfi.nl Lada 112 1.6 8V Bosch Motronic ‘05 GSI Fitting Instructions /Inbouwinstructie /Manuel de Montage / Einbauanleitung OverviewSystem/SysteemOverzicht/ImplantationGénérale/System Übersicht 13 14 10 1 3 6 2 2 2 2 4 12 8 9 Fitting order / Montage volgorde / Ordre de montage / Einbau reihenfolge Nr. Description / Omschrijving / Description / Umschreibung 1. Remove inletmanifold /Verwijder innlaatspruitstuk /Enlever collecteur d’admission / Entfernen Ansaugkrümmer 2. GSI-injectors /GSI-injectors /Injecteurs GSI/ GSI-Einspritzventile 3. Mounting inletmanifold/ Montage inlaatspruitstuk/ Montage du collecteur d’admission/ Einbau Ansaugkrümmer 4. Preparation copper pipe /Voorbereiding koperleiding /Préparation tube de cuivre / Vorbereitung Kupfer Gasleitung 5. Preparation wiring harness /Voorbereiding kabelboom /Préparation câble principal/ Vorbereitung Kabelsatz 6. Cable leadthrough / Kabeldoorvoer / Passage de faisceau / Kabeldurchführung 7. Vaporisor preparation / Voorbereiding verdamper / Préparation vaporiseur / Vorbereitung Verdampfer 8. Mounting vaporisor & ECM on bracket + wiring harness on ECM/ Monteren verdamper & ECM op steun + kabelboom op ECM/ Monter vaporiseur & ECM à contrefiche + câble principal à ECM Montieren verdampfer & ECM auf stütze + Kabelsatz auf ECM 9. Mounting bracket +Modules & connectors /Monteren steun + modules & connectoren / Monter contrefiche + Modules & connecteurs /Montieren stütze + Modul & Stecker 10. Waterconnexions / Wateraansluitingen / Connections d’eau / Wasseranschlüsse 11. Electric connections / Electrische aansluitingen / Connexions electriques /Elektronische anschlüsse 12. Splitter / Splitter / Répartiteur filtre / Verteiler 13. MAPsensor / MAPsensor / Sonde MAP / MAPsensor 14. Vacuumconnections / Vacuumaansluitingen / Connexions de dépression / Vakuumanschlüsse Electrical diagram /Electrisch schema /Schéma électrique /Elektronisches Schaltschema Page 11 Explanation of symbols /Verklaring van symbolen /Explications des symboles /Kurzzeichnungerklärung Page 12 Colorcodes/Kleurcodes/Code des coleurs/Farbecodes Page 12 265000-837*1 17-05-2005 3/12 www.teleflexgfi.nl Lada 112 1.6 8V Bosch Motronic ‘05 Fitting Instructions /Inbouwinstructie /Manuel de Montage / Einbauanleitung GSI 1a 1b 241505-670 + (2x) D A Ø 7 Ø 7 1c 2a 241500-001 (2x) 242000-010 (2x) M8 A D B C Ø 9 2b 2c 240219-022 (2x) + 242002-003-3 M10 (4x) B C 242000-010 (2x) 4 3 2 1 Length Injectorhoses Lengte Injectorslangen Longueur des tuyaux d’injecteur Länge Einspritzventilschlauch cil./ cyl. 1 - 470 mm cil./ cyl. 2 - 400 mm cil./ cyl. 3 - 370 mm cil./ cyl. 4 - 300 mm 265000-837*1 17-05-2005 4/12 www.teleflexgfi.nl Lada 112 1.6 8V Bosch Motronic ‘05 Fitting Instructions /Inbouwinstructie /Manuel de Montage / Einbauanleitung GSI 3a 3b 100mm 3c 3d 4a 5a Preparation/Voorbereiding/Préparation/Vorbereitung 238675-060 238675-060 ORIGINAL 265000-837*1 17-05-2005 5/12 www.teleflexgfi.nl Lada 112 1.6 8V Bosch Motronic ‘05
[ Pobierz całość w formacie PDF ] zanotowane.pldoc.pisz.plpdf.pisz.plsmichy-chichy.xlx.pl
|
|
Podobne |
: Strona Główna | : 000 - 100 Bombes Dancefloor 2011-2012, 100 Bombes Dancefloor 2011-2012 | : 000 - 100 Hits One Way Ticket, 100 Hits One Way Ticket | : 000 Enigma - The Platinum Collection. 3CD. 2009, Mp3 Enigmatic, Enigma, Enigma - The Platinum Collection. 3CD. 2009, Playlisty, info, cover | : 000 Enigmatic Hits Vol.01-09, Mp3 Enigmatic, Enigma, 100% Enigmatic Hits Vol.01-09. 2001-2003 | : 000 Chuck Berry – Best Of The Chess Years. 3CD. 2012, Chuck Berry – Best Of The Chess Years. 3CD. 2012, Playlisty, info, cover | : 000-Sensacje XX wieku - Bogusław Wołoszański -Radio Zet-mp3, Sensacje XX wieku-B.Wołoszański MP3 | : 000 Enigmatic Best Hits. 2012, Mp3 Enigmatic, Enigma, Enigmatic Best Hits. 2012, Playlista, info, cover | : 0000 info, Renesans, Medieval Music from Old Serbia - Classical - flac | : #0369 â Going to Happy Hour, - Ang, mater, ESL Podcast McQuillan Jeff mp3+PDF | : 01.13 South Park - Cartman's Mom is a Dirty Slut [Napisy PL] s01e13, ## %% ## %% ## DO NAUKI ANG South Park Sezon 1 [Napisy PL]
zanotowane.pldoc.pisz.plpdf.pisz.plslaveofficial.keep.pl
| . : : . |
|